Electrician - Seattle, WA
Average rating
5.00
5.0
Average rating
Masters Electric & Communications, LLC is licensed, bonded & insured in Washington state and is owner-operated by Justin A. Polley and Rod Chissus, who between them have over 45 years experience! Masters Electric & Communications, LLC has 1 goal: to provide our customers with professional, knowledgeable and reasonably priced electrical services that meets or exceeds their expectations. Please see our Porch interview: https://www.youtube.com/watch?v=dmxWT_uR0dA
25 years in business
Average rating
Jordan C.
12/30/2016
I have had the pleasure of knowing and working with Justin and Rod for over 10 years now. At my last job they were my go-to team for problem solving and repairing various issues at buildings I managed, and recently they completed a full kitchen re-wire and electrical panel replacement as part of a larger home renovation project. As you can imagine with any large renovation project, it is easy to become paralyzed by choice when trying to keep the project moving forward. At each decision point, Justin and Rod did a fantastic job of both communicating potential pressure points as well as providing excellent solutions to keep things going in the right direction. Furthermore, their attention to detail and pride in their work is unmatched when compared with other electrical contractors I have worked with in the past. One simply needs to look at their wiring inside of a new panel to see how much pride they take in their craft! We unfortunately ran into issues with some of the new devices that I selected during the project but they both spent countless hours researching and troubleshooting the issues to make sure my wife and I were happy with the finished product. In my experience, this is what truly sets Masters Electric apart from other electrical contractors and we absolutely plan to have them back to address the remaining work in our home. I would absolutely recommend Justin and Rod to anyone that is looking for a electrical contractor – you won’t be disappointed!
Bud K.
05/18/2016
These guys are really good. Of all the contractors we've had working on our remodel project, they are by far the best. They show up on time, get the work done and communicate clearly. I recommend them to anyone.
Lisa G.
05/18/2016
We would highly recommend Rod and Justin for electrical work.They are, well priced, communicative, and SHOW UP, on time! We are very happy with their work.
Chris G.
05/17/2016
Justin and Rod were fantastic. They rewired our entire house (removed knob and tube) and brought everything up to code. My wife and I were a bit overwhelmed with all that needed to be done but Justin was great about communicating everything. With a project like this we were pleased to see everything was done on time and on budget. I would recommend Masters Electric to anyone. They are trustworthy, considerate and honest!
Address
Seattle, WA 98117
Photo | Project | Date | Description | Cost | Home |
---|---|---|---|---|---|
![]() ![]() | new bathroom in Greenwood | Dec 2016 | To wire a new bathroom: install a dedicated 20 amp circuit from electrical panel roughly 60 ft from bathroom for a GFCI receptacle, bring another dedicated 15 amp lighting circuit from panel for vanity and genereal room light and 100 cfm low profile exhaust fan and bring a dedicated 240 volt circuit from panel for 1,000 watt in wall electric heater. | $2k | Seattle, WA |
![]() ![]() | Phinney Ridge main breaker panel upgrade | Jul 2016 | Home owner wanted to eliminate the knob & tube wiring in the home and we strongly recommended upgrading to a new 200 amp service before rewiring the home in order to accommodate the new NEC code that requires all new 120 volt branch circuits be protected by AFCI and GFCI circuit breakers. | $3k | Seattle, WA |
![]() ![]() | Ballard 200 amp Service upgrade | Mar 2016 | This home's original breaker panel size was 125 amps with a number of electrical code violations as well as being undersized for the demands of a modern home. The strike was raised above the minimum NEC code requirement using an offset rigid mast and the main panel was enlarged to 200 amps | $4k | Seattle, WA |
![]() ![]() | Emergency Storm Repair | Mar 2016 | a family in View Ridge with a new baby girl lost power when a tree fell on the power lines feeding their home and they needed power restored quickly. The mast had been torn off the house, the power lines compromised and the conduit in pieces. We installed new conduit and new power lines and secured the new mast to the exterior of the home in 1 day and city of Seattle inspected the work the next morning and by that afternoon power was restored and the family was once again safe and warm. | $900 | Seattle, WA |
![]() ![]() | Electric Car Charging Station | Sep 2014 | A condominium in north Seattle has an electric car, a Nissan Leaf and needed the electric charging station installed on the opposite side of the parking garage. The HOA provided the charging station. Masters Electric & Communications, provided over 100 ft of conduit & over 300 ft of wire. Note that through careful attention to detail we were able to install the charger in the middle of the parking bay which reduced to overall cost of installation AND increased the flexibility of the charging station by allowing the car to be charged whether it is parked nose in or backed into the stall! | $1k | Seattle, WA |
![]() ![]() | Roof service conduit & feeder upgrade | Aug 2014 | Luckily a home had to be reroofed, which required that a very poorly executed and hazardous 200 amp electrical service conduit and feeder install needed to be removed for the roofers to remove the old roof and install a new one. As you view the photos notice the difference between the old conduit, sun warped, unsupported and broken exposing the feeder wire to the elements and the new upgraded conduit & feeder installation. Although the NEC electrical code book, a.k.a. the electrician's bible, and let's face it a voluminous fun romp through electrical installation do's and don'ts, does not require it, Masters Electric & Communications provided 2 inexpensive additions to our installation to keep the homeowners & tradesmen safe and the roof service conduit & breaker panel feeder wires functioning effectively well into the future - triple the number of supports were added to support the conduit for a few extra dollars and a $20 expansion coupling was added to absorb the expansion & contraction of the conduit to prevent conduit warping and breaking. | $4k | Clyde Hill, WA |
![]() ![]() | Town & Country Fence office | Jun 2014 | Install 4 new electrical branch circuits from the main floor breaker panel to basement crew room for fridge, coffee maker and microwave and main floor computer servers and phone system interface and fire alarm. To install new communications lines, phone & internet 18 locations on 3 floors and install CAT6 rated, punch down panel, jacks & phone lines. | $15k | Lynnwood, WA |
![]() ![]() | Temporary Power Pole | Mar 2014 | Install a 125 amp temporary power pole using power from nearby transformer. This project required clear communication with the general contractor whose temporary office trailer needed power, the electric utility that had to approve the temporary additional load to the transformer and the electrical inspector. | $4k | Mukilteo, WA |
![]() ![]() | Swimming pool underwater light trouble shoot | Jan 2014 | We were hired to investigate an underwater swimming pool light (spl) that was not working. During the trouble shoot 5 potentially life threatening issues were found and rectified. (1) the 35 yr old GFCI circuit breaker that protected the pool light circuit was sticking and therefore unreliable and replaced, (2&3) a splice of the spl bond was discovered inside the conduit (see photo) AND the spliced wire was undersized thereby reducing the effectiveness of the circuit breaker to trip in the event of a ground fault and prevent a life threatening shock, (4) a splice of the 120 volt 20 amp circuit for the spl was also discovered inside the conduit which is also not allowed and not to NEC code because a splice inside conduit that eventually fills with water is much more likely to fail, (5) the 2 metal junction boxes for the spl were not bonded, i.e. they were not tied to the breaker panel ground fault, so that in the event they became "hot" with voltage a very serious or lethal shock could have occurred. All of the above wiring issues were repaired and brought up to current safety standards because the electricians know what issues to look for and how to resolve them. | $500 | Seattle, WA |